- EVERBRITE™ Protective Coating and ProtectaClear™ are unique, crystal clear coatings that is very user friendly and easy to apply. They are homogenous, one part coatings so there is nothing to mix and the coatings will not separate.
- EVERBRITE™ is suitable for internal, external or submersed use as a non-toxic, anti-corrosion protection for ferrous and non-ferrous metals, galvanized, anodized and painted surfaces. It can also be used on concrete, stone, wood and fiberglass. ProtectaClear™ is recommended for interior metal, metal that gets a lot of use like railings or metal exposed to salt or chlorine.
- Everbrite coatings have indefinite shelf life in a closed container so there is no waste.
- EVERBRITE™ and ProtectaClear™ are non conductive coatings and will prevent corrosion caused by dis-similar metals.
- EVERBRITE™ and ProtectaClear™ will remain flexible so they will not chip, crack or peel. They will not discolor or yellow with exposure or heat.
- EVERBRITE™ will refinish faded surfaces and restore the original color and protect from sun fading, salt air oxidation, moisture damage, tarnish, acid rain and other damaging elements. ProtectaClear™ will protect non-painted metals and has extra resins that are extremely resistant to salt corrosion.
- EVERBRITE™ and ProtectaClear™ are self annealing, will blend to itself and can be maintained indefinitely.
Click here for additional information and Comparison Charts of Everbrite Coatings.
Sun can cause paint to fail, causing chalking and fading. Salt air can corrode metal causing rust and ugly corrosion. Acid rain can cause permanent damage to metal and stone.
EVERBRITE™ Protective Coating can refinish faded and dull surfaces to look like new again and protect them against sun fading, salt air corrosion, acid rain, tarnishing, moisture and other damaging elements for years. Protected surfaces will be much easier to keep clean as dust and dirt cannot penetrate the paint or hang on the oxidation. Graffiti can be cleaned off of the protected surface and the paint will remain protected.
ProtectaClear™ can prevent tarnish and oxidation on plated metals, copper, brass, silver, anodized Steel, etc. The metal must be polished or cleaned first, all traces of polish residue must be removed and then ProtectaClear™ can be applied to seal the surface.
You can test the surface to see if it can be restored. Clean an area and observe it when it is clean and wet. If the color and shine come back when the surface is clean and wet, then that is how the surface will look refinished with EVERBRITE™.
Sometimes Formica and other surfaces are too far gone to restore. If the surface does not look the way you want when it is clean and wet, unfortunately, EVERBRITE™ cannot restore the surface.
EVERBRITE™ or ProtectaClear™ can be applied by wiping it on, rolling on with a high-density foam roller, spraying on the coating or dipping the object into EVERBRITE™ or ProtectaClear™
Refinishing with Everbrite Coatings is a simple 2 step process, First, the surface is cleaned and any polish or cleaner residue is removed. Second, the Coating is applied to refinish and protect the surface.
Everbrite Coatings can be applied by rolling the coating on with high-density foam rollers, spraying, dipping, painting on with a natural fiber brush or a poly sponge brush or simply wiped on the surface with an applicator.
Everbrite Coatings are one part coatings so there is nothing to mix. They are self leveling and are very easy to work with.
Surfaces like metal siding or metal buildings or roofs can be power washed or hand washed to remove chalk, dirt, any wax or grease, or any other contaminating or dirtying agents. Storage doors are normally hand washed because people have their cardboard boxes stacked right up to the edge of their space and the seals are not tight. Rinse well and make sure that water does not bead up on the surface. If it does, that means there is still soap or wax or oily residue on the surface. Click here for cleaning directions for metal buildings and roll-up doors.
Surfaces such as brass, silver, copper or other non painted metals must be neutralized if cleaned with an acid cleaner and then should be wiped with xylene or denatured alcohol to insure all contaminates are removed.
IF THE SURFACE IS CLEANED WITH AN ACID CLEANER, THE SURFACE MUST BE NEUTRALIZED BEFORE APPLYING THE COATING. Use EZ Prep Cleaner & Neutralizer or calcium carbonate or a baking soda wash to neutralize the acid. Water rinsing will not remove all of the acid. The acid will react with the solvent and will create problems such as black streaks.
EVERBRITE™ and ProtectaClear have an indefinite shelf life in a closed container. Unlike 2 part coatings which are wasted if not used in a short time once mixed, there is nothing to mix. This means that if you get interrupted while applying the coating, simply pour the unused Coating back into the container, put the top on and you can resume where you left off at another time. ***Do not pour contaminated coating back into the original container. Do not allow the coating to freeze.
On exterior applications on painted metal, EVERBRITE™ will need to be reapplied when the surface starts to look dull. Depending on the elements and U.V. exposure, this will be about 5 to 10 years. On homes where awnings or foliage shade the home, only the sides exposed to the sun would need to be refinished.
On fiberglass, EVERBRITE™ will have to be reapplied every 1 to 3 years. The number of years of protection vary by the intensity of the damaging elements and use of the surface.
On brass, copper, bronze, stainless steel etc. the length of time will depend on the usage and elements it is exposed to. On interior applications, the metal will not need re-application for many years unless it gets a lot of wear. On exterior applications, the coating may need to be reapplied more often
EVERBRITE™ and ProtectaClear™ do not need to be stripped to be reapplied. Simply clean the surface and reapply. EVERBRITE™ and ProtectaClear™ are self annealing and will bond to itself to create a whole new, one part envelope of protection.
In many cases, metal surfaces are repainted simply because they have become dull and faded. Refinishing with EVERBRITE™ Protective Coating is less expensive, faster, easier and achieves more permanent results than repainting.
Just repainting metal cannot protect against salt air corrosion. Repainted surfaces will fade faster than baked on paint, and may crack, peel, blister, chip and ruin the look of your property. Unless it is absolutely necessary to paint, it is much better to refinish your baked-on finish. If the surface are already repainted, you can now seal them with EVERBRITE™ Protective Coating preventing moisture and sun damage. Click here for pictures of siding that is too far gone to be restored.
EVERBRITE™ Protective Coating can be applied in temperatures from approximately 40º F up to 100º F. The temperature of the metal is more important than the air temperature. At 65°F air temperature, the metal can reach over 100°F in direct sunlight while in the shade, the metal will be around 75°F. DO NOT APPLY EVERBRITE™ IF THE METAL TEMPERATURE IS ABOVE 100°F. The coating will flash off before it can self level and will fail. If the metal is too hot to comfortably hold your hand on it for more than a few seconds, it is probably too hot for application of the coating.
If applying to vertical services, watch for runs or sags if applying between 40º and 50ºF. If you get sags, simply wipe them out with a applicator or clean, white, lint free rag damp with EVERBRITE™. If you make a mistake, it can be fixed by removing the EVERBRITE™ with xylene and reapplying.
The best temperature to spray in is over 50° F. If you spray vertical walls or doors at lower temperatures, watch very carefully for sags or drips as the coating will dry more slowly and can run down the surface. If this happens, simply wipe them out with an applicator wet with EVERBRITE™ or a solvent like xylene or denatured alcohol.
EVERBRITE™ should not be applied if the temperature of the metal is above 100°F. If the surface is too hot, the coating will flash off before it has a chance to completely coat the surface. If you are spraying on a very warm day, it is best to NOT apply EVERBRITE™ in the direct sun where the temperature of the wall is too hot.
Back to Top
Do NOT apply EVERBRITE™ to soft rubber or soft vinyl as the solvent can harm them.
Hard vinyl signs and vinyl siding have successfully been refinished with EVERBRITE™. If in doubt, test a small inconspicuous area.
EVERBRITE™ cannot help if the surface is already too damaged to be restored. For example, once salt air oxidation is so bad that the metal is extremely pitted or rusted, or if there is no paint left on the surface. Peeling paint must be repaired prior to being coated with EVERBRITE™ Protective Coating. It is best to protect property prior to extreme damage.
EVERBRITE™ will prevent acid rain damage but nothing can fix it once the surface is etched and stained.
Most new metal buildings or rollup doors are coated with a polyester coating which will usually burn off in 2 to 3 years. It is best to wait until this coating is gone before refinishing and protecting with EVERBRITE™. The exception to this is if protection is necessary from salt air or acid rain.
Refinishing with EVERBRITE™ Protective Coating is economical due to the high coverage rate and longevity of the coating. The cost for the material is between 17 and 47 cents per square foot depending on volume. Labor is less expensive than painting because there is no masking necessary.
You can purchase EVERBRITE™ Protective Coating directly from Everbrite, Inc. securely on our website (See Online Catalog on links above) , by fax or by phoning our office during regular business hours (7:30 a.m. to 4:30 p.m. PT) at 800-304-0566. We will also be happy to help you figure out how much EVERBRITE™ or ProtectaClear you will need for your project and will ship your order right to your door.
Thank you for the question. Yes, ProtectaClear is recommended for protection of the brass and other components on your clocks. Especially by the ocean where you get salt air corrosion, this is very important. Another benefit is that EVERBRITE™ is practically weightless and will not affect the performance. The weight of the dry film is 0.0003 lbs. per square foot.
At this point, we do not have a distributor in Canada, however EVERBRITE™ Protective Coating can be purchased from EVERBRITE, Inc. and shipped to you. The shipping charges will vary depending on your location. EVERBRITE™ can also be shipped to other countries in the same manner.
If you mess up the application or get EVERBRITE™ on a surface that you didn't mean to get it on like window glass, the coating can be removed with xylene or other solvents like lacquer thinner or denatured alcohol. Make sure to test an area of the surface to make sure that the solvent will not harm it.
If the aluminum or other metal was cleaned with an acid based cleaner and was not neutralized, the solvent in the coating reacting with the acid will cause black streaks. Acid cannot be totally rinsed off with plain water, a calcium carbonate or baking soda wash must be used to neutralize it before any solvent based coating is applied.
ProtectaClear™ is food safe when it is cured and is recommended for interior metal. Do you use this cookware often or is it mainly decorative? If you use whisks or other utensils, may scratch off. It may also not do well if you use very high heat to cook. If your pots are mainly decorative, EVERBRITE™ would work well for your copper.
ProtectaClear will also protect your copper backsplashes, copper bars, copper hoods and other copper in your kitchen, keeping it beautiful and easy to clean.
Everbrite Products are not sold in stores but can be shipped directly to you by UPS or US Post Office. Shop 24 Hours a Day, 7 Days a Week, 365 Days a Year on our Secure Online Store or Call us Toll-Free Monday - Friday 7:30 a.m. to 4:30p.m. Pacific Time except major holidays.
Do you have questions? Ask us and we will send you an answer ASAP. Your information will be kept confidential. We do NOT sell, rent, disclose or otherwise abuse your information.
Home Directions Products FAQ's Testimonials Contact Us
|
